PDA

View Full Version : Drive shaft


ama_zuki
04-09-2006, 10:12 PM
Whats everyone doing for their drive shafts with yj's spoa? slipyoke or extensions?

Roach2004
04-09-2006, 10:55 PM
Custom driveshafts!

mahana79
04-09-2006, 11:13 PM
I just had spacers bigok

ama_zuki
04-09-2006, 11:59 PM
I just had spacers bigok
how many?

ama_zuki
04-09-2006, 11:59 PM
Custom driveshafts!

CV shafts? or have them extended?

mahana79
04-10-2006, 12:05 AM
how many?

Sorry, I had a 1" spacer on both the front and rear.

On the front I had it up at the t-case and on the rear I had it down at the pinion. bigok

purevil71
04-10-2006, 12:37 AM
1/2" spacer and a Rat Adapter up front on my stock sami D-shaft.
Rat adapter on the rear with a Toy CV shaft.

Skut
04-10-2006, 03:27 AM
cv yota , just got 1 for my b day!

Billjohn
04-10-2006, 09:56 AM
KAD up front and Tom Woods out back...

ama_zuki
04-10-2006, 11:18 PM
what if im broke?

purevil71
04-11-2006, 01:16 AM
what if im broke?
Stock......(and try not to break it)
:mrgreen:

xanthias
04-12-2006, 05:17 AM
You can also get 1 or 2 inch extended yokes from Trail Tough

ama_zuki
04-12-2006, 08:41 AM
Stock......(and try not to break it)
:mrgreen:
can i drive it on the street wit stock shafts?

uglytrk
04-12-2006, 08:50 AM
I run a stock rear on the road and a homemade on the trail, front I had to make one stock falls 6" too short

mahana79
04-13-2006, 12:13 AM
can i drive it on the street wit stock shafts?

You will probably be OK on the street with stock shafts. key word PROBABLY. You shouldnt run into problems unless you stat to flex it out. by the way i hope the YJ brackets worked out for ya.

purevil71
04-13-2006, 12:30 AM
I ran stock shafts out back for a while untill I discovered the Toy CV shaft. Biggest issue I had with them was u-joints.

Most of the U-joints I blew were off-road, only had one blow in the road. Funny thing watching your rear D-shaft pass you in a corner going 55....lol

neil_04
04-13-2006, 09:09 AM
do what i did two days ago find a good welder with a nice shop and have him cut and modify what you need unless this is a D.D. not the most balanced drive shaft buit very effective offroad. It gets expensive trying to have something custom made. the places i went for my back d shaft wanted 500$ plus. if you are broke i would talk to some of these guys that have been using spacers

ama_zuki
04-14-2006, 12:52 AM
do what i did two days ago find a good welder with a nice shop and have him cut and modify what you need unless this is a D.D. not the most balanced drive shaft buit very effective offroad. It gets expensive trying to have something custom made. the places i went for my back d shaft wanted 500$ plus. if you are broke i would talk to some of these guys that have been using spacers
Its gonna get cv shafts, but untill then its a street machine

joejna
04-21-2006, 06:17 PM
i have little vibration on driveshaft with SOA 6" i put spacers on driveshaft but still vibrates a little i had before a 6 or 8 degree axle shim but now i put a 4 degree do you guys think i will need a 2 degree to correct vibration???